#Saitek x52 pro mini stick problem how to#
#Saitek x52 pro mini stick problem full#
#Saitek x52 pro mini stick problem software#

I figure that somehow I can do straight and level flight (with a bit of trim) when the stick is in its neutral position, but the way it's calibrated right now, I need way too much trim to keep it level.Р”В¬an someone please explain to me what I need to correct this behavior? I've read several posts that say 'You need to calibrate', but the calibration screen looks correct to me. Once I get off the ground a bit, I let the joystick back to its neutral (center) position and the plane wants to do a direct dive-bomb. My problem is (I'm using FSX by the way) that when I take off, I need to pull back quite a bit on the yoke to pitch up and take off.

#Saitek x52 pro mini stick problem software#

I've have the latest drivers, and used the included software to 'Calibrate', but to tell you the truth, it appears that it is calibrated already.

#Saitek x52 pro mini stick problem how to#

Get rid of the software and use FSUIPC, it's not too hard to learn, and you can even program profiles for different planes.I purchased the Saitek X52 joystick, and I'm not sure exactly how to calibrate it. Only a system reboot would solve the issue. I could unplug the stick too, but the courser kept on running to the left. M.I had that too, it's been caused by their software on my machine. !T4JCSLpb!qN0xVwYqh7hBy5F12qGX98NWCOBaDvXsfH7wwAeJ46g third party aircraft, it will be a nightmare to get everything working as it does with the Saitek software!Р”Р„nyone else have this? A little video here, though I am sure it's hardly needed:

#Saitek x52 pro mini stick problem full#

I don't know if you'll come back to this thread Michael, but just to confirm, you uninstalled all the Saitek software and then only installed the drivers? I have a full setup of commands via the programming software and I envisage, if if it works with my PMDG etc. PMDG support have told me not to use FSUIPC to programme their MD-11 for instance, as it causes issues. The problem with using FSUIPC is that some a/c don't like it. (I can fortunately test this as I have two X52s and am going to swap them over today to see if the wandering cursor still occurs - little doubt that it will. The folks at MadCatz have been quite good and are investigating - they have offered to replace the X52 for a new one, but I doubt that the hardware is the problem. !Р”Р„nyone else had this cursed cursor issue and been able to find a permanent fix (other than ditching the X52!). I love the hardware but I am really fed up with Saitek's software! I can't use USB3.0 on this PC as the Saitek software kept causing BSODs with the Intel USB controllers (a known issue apparently), there always seems to be something! If I had $1 for every time I've had to reinstall the Saitek drivers. I simply have to unplug the X52 and then plug it back in again. But now it happens on and off (not all the time, thank god) for apparently no reason at all. I thought I'd solved it - it seemed to happen mostly if I woke the PC up from standby mode.

(I am talking about my main mouse here, not the cursor on the X52 itself). Took a while to discover that it was caused by the X52 - if I unplug it and then back in again the cursor stops its movement. It was still usable but went back to its trek across the screen when I left the mouse alone. A few weeks ago I suddenly started seeing my mouse cursor moving steadily from the left to right side of my monitors all by itself (a brand new 'amusement' provided for me by my PC I never know what it's going to conjure up next!).